over balance 超平衡
over driven worm gear 蜗杆在上方的蜗轮蜗杆传动
电梯英语翻译,电梯英语词汇表,
over heating 过热 over power 过负载
AC variale speed 交流调速
over run 超程
AC(alternating current) 交流电
over sling 上吊架
acanning cycle 扫描周期,扫描循环
over slung type 上悬吊式
acceleration control system 加速度控制系统 over speed switch 超速开关 acceleration(accel)rate 加速器
overall cost 总成本,总费用
accelerator 加速器
overcurrent 过电流
acceptance of lift 电梯验收
overcurrent relay 过流继电器
acceptance period 验收阶段
overcurrent release 过电流释放
acceptance test 验收试验
overcurrent vreaker 过流断路器
acceptanec certificate 验收证书
overhang 悬臂式,外伸的
access door 检修门 overhang traction sheave 悬臂式曳引轮 access forbidden 禁止入内
overhaul 大修
access lift 通道电梯
overhead 顶层空间,顶部
access security 通道防卫
overhead beam 顶楔
access switch \"通道开关,维修用开关\"
overhead height 顶层高度,顶部高度
access way 进出通道
overhead machine 顶置曳引机
accessibility \"可通达性,接近的,难易程度\" overhead pulley 顶部轮 accessible 允许进入
overhead sheave 顶部绳轮
accessible space 允许进入的场地
overhead structure 顶部构件
accessory \"配件,附件\"
overhead(O/H) 顶房上置
accident 事故
overhoisting limit switch 井道上部限位开关
accident insurance 事故保险
overlap 重叠
accident prevention 事故预防
overlay (墙壁等)饰面
accidental contact 触电
overload 超载
accidental operation 误操作
overload buzzer 超载蜂鸣器
accordion door 折叠门
overload control 超载控制
accumulation 累积 overload device 超载装置 accumulator 蓄电池
overload indicator 超载装置
AC-GL machine 交流无齿曳引机
overload lamp 超载灯
acoustic \"听觉的,声音的\"
overload test 超载试验
acrew die 板牙
overload warning 超载报警
activate \"启动,触发\"
overload weighting microswitch 超载微动开关
active mode 主动模式
overrun 越程
actual condition \"实际状况,实际条件\"
overshoot 过冲,速度调节过量
actual load 实际载荷
oversize 大号,超大号
actual state 实际状况
oversize reamer bolt 大号螺栓
actual value 实际值
overslung car 上方悬臂轿厢
actuate \"开动,操作,激励\"
overspeed 超速
actuating linkege 操作连杆
overspeed governor 限速器
actuating magnet 操作磁铁
overspeed governor switch 超速保护装置
actuation time 动作时间
overtravel 越层
actuator \"操纵机构,激励器,螺线管\"
overturn moment 倾倒力矩
actuator bracket 调节器支架 overturn-proof 房倾倒装置 actuator plate 调节板
overweight 超重
ACVF drive 交流调频拖动
over-wind protection switch 防过卷开关
ACVF system 交流调频系统
owner 物主,所有者
ACVF(AC varible frequency) 交流调速
oxidate 氧化
ACVV dirve 交流调压拖动
p.c. motherboard 印刷电路母板
ACVV system 交流调压系统
package part 零件组合
ACVV(AC varible voltage) 交流调压
packaging material 包装材料
adaptation \"适应,匹配\"
packed landing bolt 门厅用配套螺栓
adapter PCB 选通脉冲印刷电路板
packing 包装
adapter(adapator) 适配器
packing charge 包装费用
adapting 选配
packing cost 包装成本
电梯英语词汇翻译
adaptive control system 自适应能力控制系packing ring 密封环 统 pad 衬垫,垫片 addendum \"齿顶高,附录\" paddle fan 叶片式通风扇 addendum circle 外圆 paging service 传呼服务 adding working drawing 附加加工图 paint 油漆 addition \"附加物,加法\" painting 涂漆,涂装 additional materials 附加材料 pale 踏板 address 地址 pallet type moving walking 平板式自动扶梯 adhesion \"胶,粘合胶\" pallets 踏板 adhesion protective oil 防粘油 pan 盘 adhesive foil 胶粘薄膜 panel 板,扇,屏 adhesive tape 胶带 panel door 板式门 adjacent 邻近的 panorama lift 观光电梯 adjacent car \"相邻轿厢,相邻电梯\" panoramic lift 观光电梯 adjacent entrance 相邻出入口 pantagraph 壁杆 adjusment 调试 pantagraph type hydraulic elevator 壁杆式液压梯 adjustable condensor 可变电容器 paraffin 煤油,石蜡 adjustable resistance 可调电阻 parallel 并联 adjustable spanner 可调扳手 parallel circuit 并联电路
adjustable speed electric drive 调速电力拖动 parallel continuous arrangement 并列设置 adjustable wrench \"活动扳手,可调扳手\" parallel key 平键 adjusting screw 调节螺丝 parallel lay rope 平行捻钢丝绳 adjustor 调试员 parameter 参数
parapet 防护栏杆
parasitic signal 寄生信号 翻译公司 专业翻译词汇
administation overjhead rate 管理费用标准 parking 驻停
parking car 驻停轿厢 administration cost 管理成本
parking device 停靠装置 administration expenses 管理费用
parking floor 驻停楼层 advance door opening 提前开门
parking landing 驻停层站 advance payment 预付款
parking signal light 驻停信号灯 advanced \"提前的,先进的\"
parking switch 驻停开关 advanced carriage 超前拖板(选层器)
advancing position reference value 超前位置parking zone 驻停区
part 零件 参考值
part for jamb and sill installation 门套和门坎安装用零件 aerial cableway \"空中缆车,架空索道\"
partial load 部分载荷 aerial ropeway \"空中缆车,架空索道\"
partial view 局部视图 aerial tramway \"空中缆车,架空索道\"
partition 分隔,隔板 aesthetic 美观
parts for closer installation 关门机安装用零件 after sales service 售后服务
parts layout 零件配置图 agency 代理
parts list 零件清单 agenda 议程
pass button 直驶按钮,不停按钮 air cord (门机用)航空钢丝绳
pass switch 不停开关,直驶开关 air purifier 空气滤清剂
passage way 通道 air ventilator 通风管
passenger 乘客 air-bleed 空气分泄器
passenger access time 乘客登梯时间 airborne noise 空气传播噪声
passenger arrival rate 乘客到站率 air-condition 空调
passenger car 载客轿厢 air-gap 气隙
passenger carried per minute 每分钟载运乘客人数 alarm 警报
passenger conveyor 自动人行道 alarm bell 警铃
passenger exit time 乘客出梯时间 alarm button 警铃按钮
passenger journey time 乘客乘梯时间 alarm buzzer 警报蜂鸣器
passenger lift 乘客电梯 alarm circuit 警报电路
passenger loading time 乘客进入电梯时间 alarm system 警报系统
ALC(autoclaved light-weight concrete) 蒸压passenger transfer time 乘客进出电梯时间
passenger transit time 乘客转乘电梯时间 轻质混凝土
passenger transported per minute 每分钟载运乘客人数 alcove arrangement 电梯U型排列法
passenger unloading time 乘客走出电梯时间 algorithm 算法规则系统
passenger waiting time 乘客候梯时间 align 校正
aligning template 校正样板 passenger way 走道 alignment 校正 passenger/freight elevator 客货两用电梯 alignment gauge 校正量规 passenger-and-freight elevator 客货两用电梯 alkali 碱 passenger-goods lift 客货电梯 all-computer-controlled 计算机全控的 passing chime 到站钟 allocation \"分配,分派\" passive mode 被动模式 allocation of landing call 层站呼梯指令分配 password 通行令,口令 allowance \"允用误差,加工余量\" patent 专利
allowble stress for temporary load 允许暂时patenting 线材(拉后退火) 应力值 paternoster 链斗式升降机 alloy 合金 pattern 图形 alloy steel 合金钢 pavement lift 自动人行道 alteration 改进 pawl 棘爪 alternate floor 隔层 PC board 印刷电路板 alumina 氧化铝 PCB (printed circuit board) 印刷电路板 aluminum 铝 PCB assembly frame 印刷电路板组装架 aluminum alloy 铝合金 PCB bay 印刷电路板抽屉盒 aluminum bronze 铝青铜 PCB connection strip 印刷电路板插接条 aluminum cladding 铝制包层 PCB edge connector 印刷电路板边缘插接器 alumite 防蚀铝 PCB plug-in check 印刷电路板插接通电检查 alundum 氧化铝 PCB rack 印刷电路板插架
peak current 峰值电流 peak load 高峰负载 翻译公司 专业翻译词汇
peak service 高峰交通服务 ambient 环境的
peak value 峰值 ambient noise 环境噪音
pedestal bearing 托架轴承 ambient temperature 环境温度
pension fund 退休基金,养老基金 ammeter 安培计
penthouse 楼顶机房 ammonia 氨
pentode 五极管 amperage 电流强度
perambulator 手推车 ampere 安培
percenage 百分比 amplification 放大
percentage load 负载百分比 amplification stage 放大等级
performance 性能 amplifier 放大器
performance characteristic 性能特征 amplifying tube 放大管
performance curve 性能曲线 amplitude 幅度
performance guaranteed maintenance 性能保证维修 analog adder 模拟加法器
performance index 性能指标 analog computer 模拟计算机
performance test 性能试验 analog speed card 模拟曲线板
analog-digital converter 模拟-数字转换器 performed rope 预成型钢丝绳
period of guarantee 担保期限 analogue(analog) 模拟
periodic maintenance 定期维修保养 analysis 分析
periodic test 周期性试验,定期试验 analysis mode 分析模拟
periodical examination and test 定期检查和试验 anchor bolt 地脚螺栓
periodical inspection 定期检查 anchorage \"锚具,锚定\"
peripheral 圆周的 angle bar 角钢
peripheral force 圆周力,切线力 angle guide 角铁导轨
peripheral speed 圆周速度 angle iron 角铁
periphery 圆周,圆柱体表面 angle iron frame 角铁框架
permanent 永久 angle of contact 接触角
permanent magnet 永久性磁铁 angle of deflection 导向角
permeability 磁导率,渗透性 angle of inclination 倾斜角
permissible deviation 允差 angle of lead 导程角
permissible stress 许用应力 angle of traction 曳引机包角
permitted stress 许用应力 angle of wrap 包角
personal code 个人电码 angle steel 角钢
angular contact ball bearing 向心推力球轴承 petroleum 石油
angular contact bearing 角面接触滚动轴承 PG (pulse generator) 脉冲发生器,编码器
PG constant 编码器解像度,编码器常数 angular gear 斜齿轮
PG size 编码器解像度,编码器常数 angular retardationg 角减速度
angular velocity 角速度 anneal 退火 annealing 退火
annual inspection 年检 annual report 年度报告
annunciator \"报音器,声音合成器\" anode 阳极
anodize 氧极氧化
ANSI(America Nationa Standard Instirute) 美国国家标准协会
anti-clockwise 逆时钟方向 anti-corrosive paint 防腐蚀漆 anti-creep 防蠕动
anti-friction bearing 抗摩擦轴承 anti-nuisance 防干扰
anti-nuisance device 防捣乱装置 anti-phase braking 反向制动 anti-phase current 反相电流
anti-rebound of compensation rope device 补偿绳防跳装置
anti-residual 防剩磁 anti-resonance 抗谐振
anti-reversion device 防反转装置 anti-rust 防锈
翻译公司 专业翻译词汇 anti-stall 防空转
anti-vibralion pad 防震垫
APM(automatic people mover) 自动人员运输机
apparen power 视在功率 apparent output 视在输出 applicant 申请人 application 申请
application guide 应用指南 aprons 裙板 arbour \"轴,杆\"
arc chamber 电弧隔离室 arc protection 防电弧 arc quenching 熄焊弧 arc shield 电弧屏蔽 arc suppressor 灭焊器 architect 设计单位 architecture 建筑学 architrave 门框 area 面积 arm \"臂,支路\" armature 电驱
armature coil 电驱线圈 armature current 电驱电流
armature lamination 电驱铁芯片 armature shaft 电驱轴 armature spider 星形轮 armature winding 电驱绕组 armoured 蛇皮管的
armoured cable 蛇皮管电缆 armoured conduit 导线管 arrangement 布置 arrival bell 到站铃
phase 相位
phase advance 相移超前 phase angle 相位角
phase angle control 相位角控制 phase difference 相位差 phase failure 断相
phase failure relay 断相保护继电器 phase lagging 相移延迟 phase lead 相移超前 phase loss 断相
phase monitoring relay 相位监控继电器 phase reversal 反相,相序逆转 phase reversal relay 换相继电器 phase reversed 反相
phase shifting 相移的,移相的 phone connector (通讯线)插头 phosphorus 含磷的
翻译公司 翻译词汇
photo detector 光监测装置 photo eye 光电监测器 photo switch 光电管开关 photocell switch 光电管开关 photo-coupler 光电耦合器 photo-diode 光电二极管 photo-electric cell 光电管
photo-electric device 光电管装置
photo-electric passenger detector 光电乘客监测器 photo-electric protection 光电保护
photo-electric safety device 光电保护装置 photo-electric switch 光电开关
pick-up (继电器)吸合,得到信号 picture plane display 画面显示
PID (proportional-integral-differential) 比例-积分-微分 piece rate 计件单价 piece wages 计件工资 piercing 冲孔 pillow block 架座 pilot light 指示灯
pilot production 试生产 pilot valve 导向阀 pin 销钉
pin adaptor 插头转接器 pincer 钳子 pine 松木
pinion 小齿轮,齿节 pipe 管子
pipe bend 弯管 pipe clamp 管箍
pipe connection 导管连接 pipe fitting 管道配件
pipe rapture valve 管道破裂保险阀 pipe system 管道系统 pipe threading 管螺纹 pipeline 管道
piping 配管,管路 piston 活塞,柱塞
piston type cylinder 柱塞式油缸 pit 底坑
arrival buzer 到站蜂鸣器 arrival floor 到达楼层 arrival gong 到站钟 arrival rate 到站率
article of consumption 消耗品 artificial intelligence 人工智能 artistic 工艺
artistic face 工艺表面
asbestos packing 石棉盘根 ascending 上升
ASIC(application specific integrated circuit) 专用集成电路 assemble 装配
assembler language 汇编语言 assembly of hinge 铰链组装 assign 分配
astragal 装饰镶条
atmospheric influence 大气影响 attachment 附件
attendant control 有司机控制
attendant control compartment 有司机控制盒
attendant operation 有司机操作 audible signal 音响信号
audio tape recording 磁带录音 authority \"当局,核准部门\"
authority of lift acceptance 电梯验收部门 authorized \"授权的,核准的\" authorized user 核准使用者 auto-adaptation 自适用
AutoCAD 自动计算机辅助设计 autographic recoder 自动记录仪 automatic 自动的
automatic allocator 自动分派器 automatic by-pass 自动直驶
automatic center opening sliding door 自动中分式滑动门
automatic closer 自动关闭门 automatic dispatch 自动调度 automatic door 自动门
automatic homing 自动回基层 automatic landing 自动停站
automatic landing system by spare battery 靠备用蓄电池的自动停站设备 automatic leveling 自动平层
automatic lubricator 自动润滑装置 automatic parking garage 自动停车库 automatic parking system 自动停车系统 automatic relevelling 自动平层校正 automatic rescue device 应急救助装置 automatic return 自动返回
automatic telescopic center opening sliding door 自动中分式折叠滑动门
automatic telescopic sliding door 自动折叠式滑动门
automobile lift 汽车电梯 autowalk 自动人行道
auxiliary apparatus 辅助装置 auxiliary brake 辅助制动器
pit access door 底坑检修门 pit access ladder 底坑出入爬梯 pit depth 底坑深度 pit ladder 底坑爬梯 pit lamp 底坑灯
pit protection railing 底坑保护栅栏 pit ptotection gred 底坑护栏 pit safe plate 底坑安全板 pit screen 底坑防护网
pit stop switch 底坑停止开关 pit switch 底坑开关 pit tanking 底坑防水层 pitch 螺距
pitch circle 齿节 pitch diameter 节径 pitch line 节距
pitch of teeth 齿节距 pivot pin 中心销钉 pivot point 支点
pivoted guuide shoe 活动导靴 plain bearing 滑动轴承 plane 刨,刨平
planetary machine 行星齿轮机器 planing machine 刨床 plank (轿厢架)底楔 plastic foil 塑料薄膜
plastic materials 塑料材料 plastics 塑料 plate 板
plate counterweight 板式对重 plate glass 平板玻璃 plate spring 板簧
plate threshold 轿厢地坎 plated design 镀金图案 platform 轿厢底,轿底
platform frame (轿厢)底盘架 platform guard 轿厢站台护板 platform side brace 轿厢底侧拉条 platform sill 轿厢地坎 plating 电镀
翻译公司 翻译词汇
PLC(programable logic controller) 可编程序控制器 PLD(programmable logic device) 可编程序逻辑器件 pliers 虎钳
pllug socket 插座 plug 插头转接器
plug connection 插塞连接 plug pin 插脚,插销 plug receptacle 插座 plugability 可插接性
plug-in module 插接式模块 plug-in type 插接式 plug-in unit 插接元件 plumb 铅垂侧直,铅垂 plumb bob 铅垂重物,铅垂 plumb line 铅垂线
plunger 柱塞,插棒铁芯 plunger end-plate 柱塞端板
auxiliary cicuit 辅助电路 auxiliary contact 辅助触点 auxiliary drive 辅助驱动 auxiliary lock 辅助锁
auxiliary materials 辅助量 auxiliary value 辅助材料 auxiliary winding 辅助绕组 available area 有效面积 average 平均
average car load 平均轿厢负载
average dispatching interval 平均调度间隔时间
average interval 平均调度间隔时间
average passenger waiting time 平均乘客侯梯时间
average response time 平均应答时间 average waiting quest 平均乘客量
average waiting time 平均乘客侯梯时间 axial flow fan 轴流式风扇 axis 轴线 axle 轴
plunger head 柱塞顶部
plunger head sheave 柱塞顶部轮 plunger limit switch 柱塞限位开关 plunger return 柱塞复位 plunger runby 柱塞越程 plunger sheave 柱塞滑轮
plunger stopper 柱塞挡止器,柱塞防脱装置 plunger stroke 柱塞行程
plunger type cylinder 柱塞式液压缸 plus 加,正极 plyphase 多相
plywood 三合板,胶合板 pneumatic 气动的
pneumatic door operator 气动开门机
point fo common connection (PCC) 普通接点 pointer 指针 polarity 极性 pole 电极
pole coil 电极线圈 pole core 电极芯子 pole piece 极靴 pole shader 极帽
pole-changing 变换极性的 luggage lift 行李电梯
pole-piece lamination 极靴铁芯片 lumen 流明(光通量单位)
polish 抛光 luminous indicator 发光指示器
population 人口,人数 Lux 勒克司(照明单位)
position 位置 machinability 切削性
position actual value 位置实际值 machine 曳引机
position control 位置控制 machine beam 曳引机承重钢梁
position control loop 位置控制回路 machine beam plate 曳引机支撑板
position control system 位置控制系统 machine bed 曳引机座
machine bed inserting mortar 曳引机座(砂position controller 位置控制器
position feed-back loop 位置反馈回路 浆)灌缝
machine bed plate 机器底板,曳引机底板 position indicator 位置指示灯
position indicator of adjacent car 邻梯指层灯 machine driving 曳引机
machine earthquake proof stopper 曳引机防position reference value 位置参照值
position reference value generator 位置参照值发生器 震挡止器
machine elevation device 曳引机高度调整装position regulation 位置调节
position regulator 位置调节器 置
position scanner 位置扫描器 machine frame 曳引机架
position sensor 位置传感器 machine installation 曳引机安装
position-dependent slowdown 按位置减速 machine isolation 曳引机隔震
machine isolation device 曳引机隔震装置 positioning trip 定位运行
positive 正电 machine language 机器语言
positive connection 刚性连接 machine No. plate 曳引机编号牌
positive drive 强制驱动 machine room 机房
positive drive service lift 强制驱动杂物梯 machine room area 机房面积
positive operation 强制操作 machine room arrangement 机房布置
post 柱 machine room depth 机房深度
potential 电位,电势 machine room height 机房高度
potentiometer 电位计,电位器 machine room inspection 机房检修
pound 磅 machine room lower 下机房
machine room of hydraulic lift 液压电梯机房 power 功率,电源
power absorption 能量吸收 machine room plan 机房布置图
power amplification 功率放大 machine room upper 上机房
power amplifier 功率放大器
power consumption 功率消耗,电力消耗
翻译公司 专业翻译词汇
power contactor 电源接触器
machine room width 机房宽度
power converter 变流器
machine room wiring harness 机房配线束
machine sheave cover 曳引机绳轮罩
machine spacing bed 曳引机高度调整底座 machine sprocket 曳引机链轮
machine supporing steels 曳引机承重钢楔 machine supporting beams 承重梁
machine supporting steelwork 曳引机承重钢结构
machine tools 机床 machined 机加工的 machinery 机械
machining 机械加工
machining allowance 加工余量 machining in general 普通机械加工 magnet 磁条
magnet brake 磁力制动器 magnet coil 电磁线圈
magnet lamination 电磁铁芯片 magnet plunger 插棒式电磁 magnet vane 隔磁板
magnetic amplifier 磁放大器 magnetic brake 电磁制动器 magnetic catch 磁闩
magnetic charateristic 磁特性 magnetic clutch 磁性离合器 magnetic detector 磁力检查器 magnetic flux 磁通量
magnetic flux density 磁通密度
magnetic leveling switch 磁性离合开关 magnetic noise 电磁噪声 magnetic pole 磁极
magnetic resistance 磁阻 magnetic switch 磁感应开关 magnetism 磁性 magnetism pole 磁棒
magnitude 大小,数量,等级 magntic core 磁铁芯 mahogany 红木 main chain 主链条 main circuit 主电路
main circuit breaker 主断路器 main circuit control 主电路控制 main contact 主触点 main contactor 主接触器 main drive 主驱动装置 main drive chain 主驱动链
main drive chain guard 主驱动链保护装置 main drive shaft 主驱动轴
main drive sprocket 主驱动链轮 main drive wheel 主驱动装置 main drive wheel 主驱动轮 main floor 基站 main landing 基站
main landing door switch 基站门开关 main lobby 大厅,主厅 main menu 主菜单 main power 主电源 main program 主程序 main reservoir 油箱 main rope 主钢丝绳 power current circuit 动力电路
power dissipation 功率消耗,电力消耗 power distribution panel 配电盘 power door 自动门
power door operation 电动门 power dumbwaiter 电动杂物梯 power factor 功率因素 power failure 停电,断电
power failure emergency operation 停电应急操作 power failure emergency service 停电应急服务 power input 功率输入 power loss 功率损失
power operated door 自动门 power operated truck 机动货车 power output 功率输出 power pack 电源装置 power range 功率范围 power source 电源 power supply 电源
power supply fluctuation 电源波动 power supply line 供电线路 power supply unit 供电装置 power unit 电源装置 power up 通电,上电 powerwalk 自动人行道
PPR (pulse per revolution) 每转脉冲数,脉冲/转 pre-announcing direction arrow 预告方向箭头 pre-assemble 预装置
precast concrete 预制混凝土 precautionary measure 安全措施 precondition 先决条件 pre-delivery 提前发货
predetermined landing 预定基站 pre-drill 预钻孔
preduction capacity 生产能力 prefabricated 预制的
prefabricated concrete 预制混凝土 preference 优先权 preferential 优先的
preferential floor 优先楼层
preferential floor service 优先楼层服务 preferential landing 优先层站 preferential service 优先服务 preferred number 优选数字 pre-formed groove 预制槽
preliminary construction work 土建准备工作 preliminary standard 基础标准 preload 预负荷 pre-locking 预锁定
pre-locking control 预锁定控制 pre-opening 提前开门
pre-opening of door 提前开门 preparatory program 预编程序 preprinted 预先印刷的 prerequisite 前提 pre-select 预选
pre-selection 预选装置 preset 预调,预设定
preset time delay 预调延时
main stop 基站 main switch 总开关 main valve 主阀门
main-drive assembly 主驱动总成,主驱动部件
maintenance contract 维修合同 maintenance control 检修控制 maintenance cost 维修成本 maintenance fitter 维修保养工
maintenance instruction 维修说明书 maintenance man 维修人员
maintenance operation 维修作业 maintenance-free 免费维修 make contact 触点闭合
maker's name plate 制造商铭牌 making button 动合按钮
male guie rail 雄导轨,带凸榫导轨
malfunction 误动作,失灵,不正常工作 mallet 木槌
managanese bronze 锰青铜 mandatory 强制的 manganese 锰 manhole 人孔
man-hour coutput 人小时产量 manipulation 利用,操纵 manipulator 操纵器,机械手 man-made fiber 人造纤维 manometer 压力计 mansion 大厦
manual brake release 手动松闸装置 manual lowering valve 手动下降阀 manual opened door 手动门
preset value 预调值 press working 预压加工 pressing 冲压,加压
press-to-talk system 按钮对讲系统 pressure 压力
pressure gage 压力表,压力计 pressure indicator 压力表
pressure project 样板项目,样板工程 pressure relief valve 压力安全阀 pressure-reducing valve 减压阀 pretension 预应力,预控力 pre-torque 预加力矩
翻译公司 翻译词汇
preventative maintenance 预防性维修 preventive maintenance 预防性维修 pre-view 预验,试映 pre-warning 预警,预告 price calculation 价格决算 price increase 提价 price list 价格表 price quotation 报价 price reduction 减价 pricing 计价
primary circuit 原电路,一次电路 primary coil 一次线圈
primary fireman's operation 主消防操作 primary machine room 主机房
primary position transmitter (PPT) 第一位置传感器 primary resistor 主电阻,定子电阻 primary wave sensor 地震纵波传感器 primary winding 初级绕组 prime cost 原价
翻译公司 专业翻译词汇 prime finish 底漆面层 manual opened hoistway door 手动厅门 primer 底漆 manual tune 人工调节,手动调节 priming coated 上底漆 manual type of control 手动控制 principle 原则,原理 manual wheel 盘车手轮 print 印刷
manualemergency operating device 手动应急print out 打印出 操作装置 printed circuit 印刷电路
manually operated down valve 手动下降阀 printed circuit diagram 印刷电路图 manualy operated door 手动门 printed circuit pattern 印刷电路图形 manufacture 制造,生产 printer 打印机 manufacturer 生产者 priority 优先性
manufacturing and sales release 生产和销售priority floor 优先楼层 许可通知 priority recall 优先召呼指令 manufacturing release 生产许可通知 priority travel control 优先运行控制 manufacturing tolerance 制造公差 private accommodation 私人住宅 maple 枫木 private code 私用电码,密码 margin 极限,边界,范围 private lift 私用电梯 marginal condition 边缘条件 private residence elevator/lift 私宅电梯 marine elevator 船用电梯 probability 概率 market concept 市场观念 probable number of stops 可能停站数 market position 市场地位 probable stops 可能停站 market report 市场报告 procedure 程序 market share 市场占有率 process 工艺过程,程序 masonry wall 转砌墙 processing control 处理控制 masonry well 砖砌井道 product descritption 产品说明书 mass 质量,块,团,大量的 profile 外形,轮廓
mass monent of inertia 惯性矩 mass production 大量生产
master 主任,硕士,主导的,精通的 master PC board 主印数电路板 master station 总站
master/slave method 主/从方法,防效方法 mat 垫块,罩面 mat switch 罩面开关 matching 匹配
materia overhead 材料管理费 material 材料
material handling 材料搬运
material supply planning 材料供应计划 matted design 闷光图案 maximum 最大的
maximum capacity 最大容量,最大能力 maximum clear opening 最大净开口 maximum load 最大载荷 maximum speed 最高速度
maximum waiting queue 最大候梯乘客量 maximum waiting time 最长候梯时间 mean square 均方
mean value 平均值,有效值〕 mean velocity 平均速度 means 方法,装置 measured load 测定值
measuring instrument 测量仪表 measuring meter 测量计 measuring range 测量范围 measuring unit 计量单位〕 mechanic 钳工
mechanical brake 机械式制动器
mechanical car position indicator 机械式轿厢位置指示器
mechanical door interlock 门机械联锁装置 mechanical door safety 机械式门安全装置 mechanical efficiency 机械效率 mechanical lock 机械式锁
mechanical reopening device 机械式重开门装置
mechanical safety shoe 机械式安全触板 mechanical switch 机械开关 mechanism switch 机器开关
mechanized parking garage equitment 机械化停车库设备
medium duty traffic 中级负荷交通 medium speed 中速,单层运行最高速 megger 兆欧表,高阻表,摇表 megohm 兆欧姆 melting point 融化点 member 部件
memorandum 备忘录 memory 记忆装置
memory address 存储地址 memory location 存储位置 menu 菜单
mercury 汞,水银 mercury arc 汞弧
mercury switch 水银开关
profile drawing 外形图 profile of groove 槽型图 profiled bar 异型钢材 profiled groove 型槽 profit 利润
profit allocation 利润分配
program 程序,计划,节目单 program controlled 受控程序 program counter 程序记数器 program library 程序库
program linkage 程序逻辑连接 program list 程序表,节目单 program system 程序系统 programmable 可编程序的
programmable timer 可编程定时器 programmed group control 编程群控 programming mode 编程模式 progressive 先进的,渐进的
progressive safety gear 渐进式安全钳装置
progressive step-switching 步进开关,步进切换 progressive type safety gear 渐进式安全钳 project 项目
project network techniques 项目网络管理 projection 投影,凸出不分,凸台
PROM (programmable ROM) 可编程序只读存储器 proof 防止
propertional controller 均衡控制器 propertional regulator 均衡调节器 proportion 比例 proportional 成比例 proposal 提议
protecting cap 防护罩 protection 保护,防护
protective coating 保护涂层 protective device 保护装置 protective earthing 保护接地 protective grating 防护栅栏 protective screen 防护屏 protective switch 保护开关 protector 保护装置,保护屏
protector rail bracket 导轨架防护装置 protector wire 防护用铁丝 prototype 样机
protrusion 凸出,突起,(墙柱)牛腿 provision 准备,防备,规定
翻译公司 专业翻译词汇 proviso clause 保留条款
proximity protection device 近门保护装置 proximity switch 接近开关 psychological 心理的,精神的 pull in 吸合
sub-contractor 分包商 sub-door closer 副关门机 sub-loop 子回路 sub-main 辅助干线
submersed type power unit 潜水式电源 submersible 潜水的
mercury vapor rectifier 汞气整流器 mercury vapour 水银蒸汽,汞气 mercuryarc rectifier 汞弧整流器
mercury-wetted relay 水银湿润继电器 merit 优点,指标 mesh 网
meshed 网式的
meshed design 网状图案 metal 金属
metal section 金属型材 metallic shim 金属垫片
meter 计量器,仪表,米,公尺 meter-in circuit 电路仪表 metering valve 计量阀 method 方式,方法 metric 公制
metric graduation 公(米)制刻度 metric ton 公吨
MG(motor generator) 电动机发电机组 MG(motor generator) set 电动机发电机组 mian terminal 大端子 mians 电力网
mians current 馈路电流
mians voltage fluctuation 电源电压波动 miantainer 维修工,维修人员 miantenance 维修,保养
miantenance agreement 维修协议 micro limit switch 微动限位开关 microampere 微安培
micro-computer 微型计算机 microcontroller 微型控制器 microfarad 微法
microfilm punched card 微缩胶片冲孔卡 micro-processor 微处理器,微机
microprodessor opertation control 微处理机操作控制
micro-switch 微动开关 microvolt 微伏
middle conductor 中线段
middle speed elevator 中速电梯 midpoint 中间
mid-rise building 中层建筑物,中高度建筑物
mild steel 软(低碳)钢
mileage recorder (电梯)运行次数记录器 mill 铣削,轧钢机(厂) milliampere 毫安培 millimeter 毫米 milling cutter 铣刀 milling machine 铣床 millivolt 毫伏特 mine lift 矿井电梯 mineral cotton 矿物棉 mineral fiber 矿物纤维 mineral wool 矿物毛 minus 负极,负数 minute 分钟 mirror 镜子
mirror finish 镜面抛光,镜面加工 submersible motor 潜水式电动机,油浸式电动机 submersible pump 潜水泵,浸油泵 sub-operating panel 副操纵盘 substation 变电站
sub-weight 辅助对重块 suction filter 吸入过滤器 suction pressure 吸入压力 suction strand 吸油绳
sudible signaling system 音响信号系统 suicide delay switch 自灭延迟开关 sulphur 硫
sump pump 油回收泵 sunk key 槽键
super high rise building 超高层建筑物 super high speed elevator 超高速电梯 superconductive 超导的 superintendent 总监 supervision 监督,检查
supervisor 监工,检查员,工长 supervisory 监督,检查 supervisory control 监控 supervisory panel 监视屏 supervisory room 监视室 supplement sheet 附页
supplementary material 补充材料
supplementray circuit diagram 补充电路图 supply piping 补充配管 supply voltage 电源电压 support 支柱,支承 support roller 支撑滚轮 supporting beam 支撑梁
supporting structure 绗架,机架 supporting truss 自动扶梯支撑绗架 suppression 抑制,排除 surface 表面
surface coating 表面涂层
surface finish 表面加工,表面涂层 surface mount 表面安装的,壁挂的 surface mounted telephone 壁挂电话 surface treatment 表面处理 surge 冲动
surge absorber 电涌(冲击波,过电压)吸收器 surge suppressor 限伏器,电涌抑制器 surplus 剩余
surplus weight 超重
suspended ceiling 悬挂式吊顶 suspension 悬吊
suspension chain 悬挂链 suspension load 悬吊荷重 suspension rope 悬挂绳
suspension rope equalize 悬吊绳均衡器 suspension sheave 悬挂轮,反绳轮 sustained load 长期负载 swing 转动,摆动 swing angle 偏转角 swing arm 摇臂 swing door 转动门
swing return 可转动打开的轿厢前帮 switch 开关
mirror finished stainless steel 镜面不锈钢 mirror-inverted 对影像的
miscellaneous 杂项的,其他的 mixing 混合
mode casting mill 铸模车床
switch arm 开关臂 switch block 开关组
switch box 开关箱,配电箱 switch bracket 开关架 switch off 开关断开 switch on 开关闭合
switching circuit 开关电路 normal illumination 正常照明
switching cycle 开关循环 normal limit switch 限位开关
switching element 开关元件 normal position 正常位置
normal terminal stopping switch 终端常位停switching noise 开关噪声
switching path 开关行程 车开关
switching position 开关位置 normal travel 正常运行
switching sequence 开关顺序 normalizing 正常化
switching station 配电站 normally closed (N/C) 常闭的
switching surge 开关峰值 normally opened (N/O) 常开的
swivel sliding guide shoe 链接式滑动导轨 nose line 凸出线
symbol 符号 nose of comb 梳齿端
synchronization 同步化 nosing 牛腿
synchronize 使同步 NOT circuit 非电路
synchronous 同步的 NOT gate 非门
synchronous motor 同步电动机 notch V型槽,V凹口
synchronous speed 同步速度 note 加注,说明
synoptical table 一览表 notice for use 使用须知
synthesizer 合成装置 nudging 强迫关门
synthetic foam 泡沫塑料 nuisance 捣乱
synthetic resin 合成树脂 number of passenger 乘客人数
synthetic rubber 合成橡胶 number of revolutions 转数
system 系统 number of segment 换向片数
system gain 系统增益 number of slots 电机槽数
system response time 系统应答时间 number of stops 停站数
table type 台式 number of turns 绕线匝数
tachogenerator 速度监测装置 numbering of elevator 电梯编号
tachometer 测速仪 nut 螺帽,螺母
tachometer generator 测速发电机 nylon 尼龙
tactile sign 触摸式标记,盲文标记 web 腹板
tail cord 引线 wedge 楔块
tail cord guide 引线保护 wedge clamp 楔块加紧
tail rope 尾绳,限速器绳 wedge guard 楔形护板
tandem 串联的 wedge shaped jaw 楔块
tank(hydra.) (液压装置)邮箱 wedge socket 楔形夹紧套
tanked pit 有防水层的井道底坑 wedge type governor 楔块式限速器
tap (变压器)抽头,引出线,攻锥 wedge type safety gear 楔块式安全钳
wedge-clamp type sagety 楔块夹紧式安全钳 tape 钢带
tape driving device 钢带传动装置 wedge-type rope socket 楔块绳头组合
tape measure 卷尺 weighing device 称重装置
tape reader 钢带传感器(读取井道信息装置) weight 重量,重砣
tape selector 钢带传动式选层器 weight closer pulley 重驼式关门滑轮
taper pin 圆锥销 weight guard channel 重驼式保护槽
taper tape 粗制绳锥,头锥 weigjht closer 重砣式关门器
tapered roller bearing 滚锥轴承 weld 焊接
tapered thread 锥螺纹 welder 焊机,焊工
tapping 抽头,引出线,攻锥 welding 焊接,焊缝
tapping screw 自攻螺钉 welding celctrode 电焊条
target 目标 welding machine 焊
target date 目标期限 well 井道
target floor 目标楼层 well depth 井道深度
target stop 目标停站 well enclosure 井道壁
T-coupling(hydra.) (液压装置)T型 well end monitoring 井道端部监测
teagle 绞盘机 well entrance 井道入口,井道门
well entrance protection 井道入口保护 well equipment 井道设备 well headroom 井道顶部 well hole 井道孔
well lighting 井道照明 well multiple 多梯井道 well pit 井道底坑 well single 单梯井道 well width 井道宽度 wheel 盘车手轮 wheel chair 轮椅
wheel chair elevator/lift 轮椅电梯 whetting machine 磨刀机 white metal 白合金 wick 油绳
wick oilier 油芯式润滑器 wide door jamb 大门套 width 宽度 winch 卷扬机 wind 风
wind 卷,缠绕
wind shield cover 整流板,挡风罩 wind up 卷绕
winding 卷,缠绕,绕组 winding data 绕组数据
winding drum machina 鼓轮式卷扬机 winding machine 卷扬机 winding number 绕线匝数 winding type 绕组型式 window 窗
电梯英语翻译,专业翻译公司翻译词汇
technical data 技术数据
technical documentation 技术文件 technical feature 技术特性
technical reference 技术参数资料 technical specification 技术规格 technical training 技术培训 teeth 齿
telealarm 遥控报警 telegram 电报 telegraph 电报机 telematics 遥控学
telemonitoring 遥控监测 telephone 电话
telephone cabinet 电话箱 telephone set 电话机 telephone station 电话台 teleregulation 遥控调节
telescopic hydraulic elevator 伸缩油缸式液压梯 telescopic jack 伸缩式液压升降装置
telescoping hydraulic elevator 伸缩油缸式液压梯 television camera 电视摄像机 tell tall call 呼梯形信号指示器 telltale 指示器
temper 退火,硬度
tempered glass 钢化玻璃 template 模板,模型 temporary 暂时的
temporary elevator 临时用的电梯 temporary load 暂时负载
temporary maintenance contract 临时维修保养合同
因篇幅问题不能全部显示,请点此查看更多更全内容
Copyright © 2019- jqkq.cn 版权所有 赣ICP备2024042794号-4
违法及侵权请联系:TEL:199 1889 7713 E-MAIL:2724546146@qq.com
本站由北京市万商天勤律师事务所王兴未律师提供法律服务